basic mechanical questions and answers pdf

Basic Mechanical Questions And Answers Pdf

File Name: basic mechanical questions and answers .zip
Size: 1452Kb
Published: 10.12.2020

What is the difference between isotropic and anisotropic materials? If a material exhibits same mechanical properties regardless of loading direction, it is isotropic, e. Materials lacking this property are anisotropic.

Mechanical Engineering Interview Questions Answers PDF

Following are frequently asked mechanical engineering interview questions for freshers as well as experienced engineering candidates. The second law of thermodynamic depicts that the total entropy of an isolated system can never reduce over time.

The shear center is a center where the force can act with no twist, whereas elastic center is located at the center of gravity. It is one of the types of a joint that are used to connect two rods, which are under compressive or tensile stress. This joint is made of steel or iron. Cotter joint is used for connecting a piston rod to the crosshead of the reciprocating steam engine.

Solder is an alloy of tin and lead. It is primarily used to make electrical joints. You cannot design any product without tolerance. It increases the chances of rejection rate and overall product cost. You utilize tolerance in part dimension to reduce cost and facilitate manufacturer.

Caustic embrittlement is a physical change in metal. In this phenomenon, the boiler becomes brittle because of accumulation of caustic soda.

Otto cycle describes the functioning of a typical spark-ignition four-stroke engine. Otto cycle is a description of what happens to gas as it is subjected to changes of volume, temperature, addition, or removal of heat.

Annealing is the process of heating any material above the recrystallization temperature and cooling after some time. This process increases the hardness and strength of metal material. The result you will get is a reduction of dislocations in the crystal structure of metal being annealed.

A uniformly distributed load is a load which is spread over a region of the beam. Here the magnitude of the load remains similar throughout the element. Fits can be categorized into three groups: 1 clearance fit, 2 interference fit, and 3 transition fit. Universal coupling is used to connect two shafts whose axes are inclined to each other. It consists of a pair of hinges, connected by a cross shaft. Pneumatic systems are significantly cheaper than other streams, i.

It can move faster and do not leak oil if they develop a leak. Mechanical refrigeration is a process by which heat is removed from a specific location using an artificial heat-exchange system. The refrigeration system can be cyclic, non-cyclic, magnetic, or thermoelectric depending on the application for which refrigeration is needed. It is a manufacturing process conducted on the lathe tool to create a pattern on a bar that can be used a handle. Thermostat makes sure to keep the engine cool at the optimum level.

It prevents decreasing the overall efficiency of the engine. Supercritical boilers do not have a heavy drum to separate steam from water and steam. They also require less steel metal. It is the smallest value that can be measured by measuring instrument. Least count can be measured using the following formula:.

A process flow diagram is a sketch which describes major equipment, plant streams, and key central loops show the relationship between system components. This diagram contains symbols to identify instruments and vessels it describes the primary flow course. It is a system which defines engineering tolerances. Bearing is a device that is placed between two components of engine for the smoother movement. It enhances the efficiency of any machine. The significant difference between pipe and a tube is that a pipe can be measured based on its inner diameter.

On the other hand, a tube can be measured based on the outer diameter. A force that causes rotation is called torque. It is a measure of how much force is required to rotate an object. Coal is a sedimentary rock that contains other elements like sulfur, oxygen, chiefly hydrogen, and nitrogen. It is the most important primary fossil fuels. Total moisture in the coil is referred to as the moisture of the bulk as a sample while the air-dried sample is called inherent moisture.

Specific Gravity is the proportion of the mass of a substance to the density of a reference substance. You can identify these metals by a spark. Mild steel gives medium and dense sparks. Cast iron gives very thick and short flashes.

High carbon steel gives long and thick sparks. It is an amount of heat that changes the property of material without increasing its temperature any further. A nuclear reactor is a plant which initiates, controls, sustains, and maintains the nuclear fission chain reaction.

It protects against radioactive radiation. Case hardening is a method of making outer surfaces harder of the steel parts. It is done to use low carbon steel. It is important to get the desired property, change electrical and magnetic properties, and relieve the stress after hot or cold working. Your email address will not be published. Post the answers of questions based on IC engine like four stroke ,two stroke engine , petrol and Diesel engine, compression ratio , knocking ,SI and CI engine and so on..

I feel very good, expected for more questions and answers with each subject of mechanical engineering. Download PDF. The questions are apt for mechanical engineering students appearing interviews.

Nice questions and answers Reply. Good question and answer for fresh BE candidates Reply. I feel very good, expected for more questions and answers with each subject of mechanical engineering Reply. Thanks for this question. Good article to learn Reply.

Questions are good but the answer are not to the point. Basic question in mechanical engineering in interview Reply. I have benefited from questions Hope the questions should up hundred Thanks Reply. I want to gain experience and knowledge in order to work Reply.

Its very use full are methods Reply.

Mechanical Engineering Interview Questions With Answers

This book was brought from archive. If you object to the publication of the book, please contact us. There are mainly two types of materials. First one is metal and other one is nonmetals. Metals are classified into two types: Ferrous metals and Non-ferrous metals.


BASIC MECHANICAL ENGINEERING Interview Questions Answers PDF free download mcqs objective type questions lab viva online quiz test bits seminar.


Mechanical Engineering Interview Questions And Answers Book Pdf

And this begs the question, what happens once our obligations come in into conflict. Ideally, you would get laid forrader of time what berth the interviewer will present you with so that you could machinate. Question: how does wonder fit in with vital thought. One manoeuvre you can use is to share your nigh late pay alternatively.

Mechanical Engineering 1. MCQ Practice Tests.

ED Jobs M. Com Jobs B. Sc Jobs B.

This part 9 of the mechanical engineering inteview questions involve the questions and answers of fluid mechanics , power plant engineering, thermodynamics etc. For further information go through these links:. Answer: Cooling Tower Classification with schematic diagram.

Download book Questions and Answers in Mechanical Engineering Part One pdf

3 comments

Orestes S.

In this page you can learn various important mechanical engineering questions answers, mcq on mechanical engineering, short questions and answers on mechanical engineering,sloved mechanical engineering objective questions answers for competitive exam etc.

REPLY

Aubine Q.

Fanuc cnc turning programming manual pdf the last hero terry pratchett pdf

REPLY

Serafina G.

The new one minute manager pdf 2012 ford mustang manual pdf

REPLY

Leave a comment

it’s easy to post a comment

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>